Vector SIMOVERT MASTERDRIVES 6SE70 VC Betriebsanleitung Seite 142
- Seite / 162
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Maintenance Vector Control Chassis Type Frequency Converter
476 869 4070 76 J AB-74 Siemens AG
12-2 Operating Instructions SIMOVERT MASTERDRIVES
12.1 Replacing the fan
The fan is designed for an operating time of L
10
≥
35 000 hours at an
ambient temperature of T
u
= 40 °C. It should be replaced in good time
to maintain the availability of the unit.
The fan assembly consists of:
♦
the fan housing
♦
a fan
The fan assembly is installed between the capacitor battery and the
motor connection.
♦
Withdraw connector X20.
♦
Remove the cable fastening.
♦
Undo the two M6x12 Torx screws.
♦
Pull out the fan assembly towards the front.
♦
Install the new fan assembly in reverse sequence.
Prior to start-up, check that the fan can run freely and check for correct
direction of air flow.
The air must be blown upwards out of the unit.
Fan Fan housing
Torx M6x12
Torx M6x12
Fig. 12-1 Fan assembly
The fan assembly consists of:
♦
the fan housing
♦
a fan.
The fan assembly is installed at the top of the chassis.
♦
Withdraw connector X20.
♦
Undo the two M8 screws of the fan assembly.
♦
Pull out the fan assembly towards the front (if necessary, tilt it
slightly downwards at the front) and lay it down safely.
Construction types
E - G
Replacement
Construction type K
- SIMOVERT MASTERDRIVES 1
- Vector Control 1
- Contents 3
- 1 Definitions and Warnings 5
- 2 Description 9
- 4 Technical Data 13
- Fig. 4-1 Derating curves 14
- EB1: Expansion Board 1 24
- EB2: Expansion Board 2 24
- Significance of the 24
- 4.2 Installation notes 27
- 4.4 Venting the heat sinks 30
- 5 Installation 31
- Fans, volumetric 36
- Regulations 41
- 7 Connecting-up 43
- 7.1 Power connections 46
- Fig. 7-4 View of the CUVC 50
- 8 Parameterization 55
- Components Order Number 59
- OP1S 6SE7090-0XX84-2FK0 59
- Fig. 8-2 View of the OP1S 60
- Selection of factory setting 62
- Start of factory setting 62
- 9 Parameterizing steps 65
- P070 Order No. 6SE70 67
- P072 Rtd Drive Amps 67
- P073 Rtd Drive Power 67
- P366 Select FactSet 67
- Automation unit 71
- (e. g. SIMATIC S7) 71
- USS via RS232 71
- P060 Menu selection 72
- P072 Rtd Drive Amps(n) 72
- P073 Rtd Drive Power(n) 72
- P109 Pole pair number 73
- P700.01 = ? 76
- P740 = ? 76
- P918.01 = ? 76
- 87654321 81
- Setpoint source 81
- MASTERDRIVES VCUSS1 (P368=4) 85
- MASTERDRIVES VC 88
- V/f characteristic (P100=1) 89
- V/f characteristic (P100=2) 90
- MASTERDRIVES VCTextile 90
- P354 is referred to P113 * ) 94
- 9.3 Detailed parameterization 96
- 3AC 380 V to 480 V 97
- 3AC 500 V to 600 V 97
- 3AC 660 V to 690 V 97
- 9.3.2 Board configuration 98
- 9.3.3 Drive setting 101
- P095 = 10,12,13 P095=11 103
- 10,13,14 104
- 11,12,15,16 104
- P384.02 = ? 106
- P384.02 = 0 106
- 10 First Start-up 115
- 11 Faults and Alarms 117
- ≠ 0 and thus a valve must be 129
- ≠ 0 and therefore a valve 130
- Check P690 SCI AnaIn Conf 136
- Table 11-3 Fatal errors 139
- 12 Maintenance 141
- 12.1 Replacing the fan 142
- (from type G) 146
- 12.13 Replacing the IVI 148
- 12.15 Replacing the PSU 149
- 12.16 Replacing the IGD 150
- 12.20 Replacing the PMU 153
- Snap catches 153
- Adapter section 153
- 13 Forming 155
- Off-circuit idle 156
- Forming time 156
- 15 Certificates 159
- Test certificate 160
- Copyright ( 161
Verwandte Produkte und Handbücher für Fahrwerkskomponenten Vector SIMOVERT MASTERDRIVES 6SE70 VC
(13 Seiten)Sharp R-409HK manuali
Manuali dei proprietari e guide per l'utente per Microonde Sharp R-409HK.
We fornisce 1 manuali pdf Sharp R-409HK per scaricare gratuitamente in base al tipo di documento: Specifiche
Kommentare zu diesen Handbüchern